TRIDENT ELECTRIC PRO • ELECTRICAL SERVICE

Lighting & Electrical Fixture Installation & Repair

Recessed lights, chandeliers, ceiling fans, dimmers, and indoor and outdoor lighting, installed safely and tested before we leave. Residential and commercial.

Indoor lightingOutdoor lightingRecessed lightingCeiling fansChandeliersDimmers & controls
Electrician installing a light fixture, lighting and electrical fixture service by Trident Electric
Direct Answer

What does lighting & electrical fixture service include?

Trident Electric installs, replaces, and repairs indoor and outdoor light fixtures, recessed lighting, chandeliers, ceiling fans, and dimmers and other lighting controls for homes and businesses. That includes the wiring, boxes, switches, and circuit checks behind the fixture, plus testing before the job is closed out.

Best fit: new fixtures, lighting upgrades, fixture replacement, ceiling fans, LED retrofits, or troubleshooting lighting circuits that flicker, buzz, or stop working.

Service Scope

Electrical work built around the actual project

Lighting affects safety, visibility, comfort, and how a space is used. Good lighting work starts behind the ceiling or wall: the box, the support, the circuit, the switch, and the load. Trident Electric handles all of it for residential and commercial spaces, so the fixture you choose is connected safely and works as intended.

The right solution depends on the existing wiring, circuit capacity, access, and the fixture itself. Our service pages are organized by job type so homeowners, businesses, and property managers can find the closest match fast.

Licensing, permits, and requirements vary by jurisdiction. For location-specific details, use the service-area directory.

What this service can cover

  • Indoor lighting installation
  • Outdoor lighting electrical work
  • Recessed lighting
  • Ceiling fans
  • Chandeliers and decorative fixtures
  • Dimmers and lighting controls
  • Fixture replacement
  • Lighting troubleshooting and repairs
At a Glance

Lighting & fixture service: key facts

DetailSummary
ServiceLighting and electrical fixture installation, replacement, and repair
Fixture typesRecessed, chandeliers, pendants, ceiling fans, track, under-cabinet, sconces, outdoor, LED retrofits
ControlsDimmers, 3-way and 4-way switches, smart switches, motion and photocell sensors
Typical timeAbout 1 to 2 hours for a standard ceiling fixture swap; longer for new locations or recessed layouts
Typical cost (national)Roughly $160 to $950 per fixture installation; recessed lights commonly run about $100 to $480 each. Fixture cost is extra
CustomersHomeowners, businesses, property managers, remodelers
Contact(855) 599-0507, 999 110th Ave NE, Bellevue, WA 98004
Fixture Types

What each type of lighting needs electrically

Different fixtures need different support, wiring, and controls. This is what we plan for on each.

FixtureWhat the electrical work usually involvesCommon issue
Recessed (can) lightsLayout, housings rated for insulation contact where needed, new cable runs, switching, dimmingCeiling access, insulation, too-low dimmer load
Chandeliers and pendantsSecure support for the weight, correct box, height setting, dimmer pairingHeavy fixtures on boxes that cannot carry the load
Ceiling fansFan-rated box or brace, separate fan/light control, balanced mountingWobble from a light-duty box
Track and rail lightingPower feed location, circuit capacity, compatible heads and dimmersOverloading a single feed
Under-cabinet and coveLow-voltage or line-voltage drivers, hidden wiring, switch or dimmer controlVisible wiring, driver hum
Outdoor and landscapeDamp or wet-rated fixtures, GFCI protection, weatherproof boxes, photocell or timer controlMoisture, tripped GFCI
LED retrofitsCompatible drivers and dimmers, replacement of failing ballasts or socketsFlicker and buzzing
Cost & Timeline

How much does lighting installation cost, and how long does it take?

Typical national ranges are $160 to $950 per fixture installation, with recessed lights often about $100 to $480 each. Your actual quote depends on the factors below. These are general market figures, not a Trident quote.

ProjectTypical timeCost drivers
Replace an existing fixture1 to 2 hoursFixture weight, ceiling height, box condition
Add a new fixture where none existsHalf day or moreNew cable, switch, ceiling or wall opening, drywall repair
Recessed lighting (per light)Varies by countCeiling access, insulation, number of lights, dimmers
Ceiling fan install1 to 3 hoursExisting fan-rated box, new support, separate controls
Outdoor lightingHalf day to multiple daysTrench or run length, GFCI, transformers, controls

What changes the price: fixture type and weight, ceiling height and access, whether wiring already exists, switch or dimmer changes, drywall patching, old-fixture removal, and any code corrections found at the box. Replacing a fixture normally costs less than adding one in a new location.

Tip: Send photos of the ceiling or wall, the fixture, and the switch location when you call. It helps us scope the job accurately.
When to Call

Common signs you need lighting or fixture work

Useful starting points, not a substitute for an inspection or diagnosis.

Fixture flickers

Persistent flickering can come from the lamp, fixture, control, wiring, or circuit.

New room needs lighting

A new layout may require circuits, switches, boxes, and fixture connections.

Ceiling fan installation

Fans need a fan-rated box or brace and wiring for the specific model.

Outdoor lighting failure

Outdoor fixtures and wiring need weather-rated equipment and GFCI protection.

Dimmer problems

Incompatible dimmers or lamps cause flicker, buzzing, poor dimming, or heat.

Old fixture replacement

Swapping an outdated fixture can reveal wiring or box issues that need correcting.

Burning smell or warm switch

Turn off the breaker and call an electrician. This can indicate loose connections or overheating.

Lights dim when appliances start

May indicate a shared or overloaded circuit, or a loose neutral connection.

Bulbs burn out repeatedly

Often points to wrong lamp type, enclosed-fixture heat, or a voltage or socket problem.

Troubleshooting

Why do LED lights flicker, buzz, or won't dim?

Most LED dimming problems come from a mismatch between the lamp or fixture, the dimmer, and the load. Common causes:

  • Non-dimmable LED lamp on a dimmer.
  • Dimmer not rated for LED, usually an older incandescent-type dimmer.
  • Load too low for the dimmer's minimum rating.
  • Loose connections at the switch, fixture, or splices.
  • Circuit or neutral problems if many lights flicker together.

What we do

We check compatibility between lamps, drivers, and the dimmer, test the load, inspect connections and boxes, and replace or rewire controls as needed. If flicker follows the whole circuit, we trace the cause rather than just swapping parts.

Call for lighting troubleshooting
How the Work Starts

A clear electrical service process

01

Choose the fixture and location

Confirm the fixture, location, controls, mounting, and electrical needs.

02

Review circuit and mounting needs

Check the circuit, box, support, and control requirements.

03

Install the electrical components

Install the fixture, wiring, controls, and associated components.

04

Test controls and operation

Verify the switches, dimmers, and fixture operation before finishing.

Safety First

Do not try to DIY hazardous electrical work

A wall switch being off does not make every conductor in a ceiling box safe. Turn off power at the breaker, verify with a tester, and use a qualified professional for electrical installation work.

For electrical faults, new circuits, wet-location work, or concealed wiring, a qualified electrician can evaluate the system and determine the next step.

Code & Safety

Requirements we plan for

  • Ceiling fans on fan-rated boxes or braces
  • Heavy fixtures properly supported
  • Recessed housings suited to insulation contact
  • Damp or wet-rated outdoor fixtures
  • GFCI protection where required
  • Dimmers matched to the load
  • Permits where your jurisdiction requires them
  • Final testing of every control
Project Preparation

Helpful information to provide

  • Property type and location
  • What is happening or being added
  • Room, circuit, or fixture involved
  • Constant or intermittent issue
  • Fixture model or specifications
  • Photos of the area when safe to take
Choosing an Electrician

Questions to ask before you hire

  • Are you licensed and insured for electrical work in my area?
  • Will you pull a permit if one is required?
  • Is the fixture, box, and support included in the quote?
  • How do you handle drywall patching or old wiring found at the box?
  • Do you test dimmers and controls before leaving?

Trident Electric is happy to answer all of these. Call (855) 599-0507.

Where We Work

Electrical service for homes and businesses

Trident Electric Pro is based at 999 110th Ave NE, Bellevue, WA 98004, and serves residential and commercial customers. Browse our service-area directory for location-specific pages, or see the full list of electrical services.

FAQ

Frequently asked questions about lighting & electrical fixtures

How much does it cost to install a light fixture?

National averages published by home-services marketplaces put a typical fixture installation at roughly $160 to $950, with about $550 as a common midpoint. Replacing an existing fixture usually costs less than adding one where no wiring exists. The fixture itself is priced separately, and your electrician should confirm the price after reviewing the box, circuit, ceiling access, and controls.

How long does it take to install a light fixture?

Swapping a standard ceiling-mounted fixture often takes one to two hours. New-location fixtures, recessed lighting, chandeliers on tall ceilings, and outdoor runs take longer because they involve cutting openings, running cable, and adding switches or circuits.

Can you install recessed lights?

Yes. Recessed lighting involves fixture selection, circuit planning, ceiling access, housings (insulation-contact rated where required), controls, wiring, and testing. The exact approach depends on the ceiling type, insulation, and equipment.

How many recessed lights do I need per room?

A common starting point is one light per 4 to 6 square feet, with spacing close to half the ceiling height. Layout depends on fixture beam angle, ceiling height, and whether you also use lamps, pendants, or natural light.

Can a ceiling fan replace an existing light?

Often yes, where a suitable electrical box and circuit arrangement exist. Fans need a box listed for fan support, because a standard light box may not safely carry the weight and motion. The mounting and wiring should be evaluated before installation.

Why do my LED lights flicker or buzz on a dimmer?

The usual causes are an LED lamp or driver that is not dimmable, a dimmer not rated for LED loads, a load that is too low for the dimmer, or loose connections. Matching a compatible dimmer to the lamps or fixture normally solves it. Persistent flicker across many fixtures can point to a circuit problem.

Can you add outdoor lighting?

Yes. Outdoor lighting can involve fixtures, wiring, controls, weather-appropriate equipment, and required protection such as GFCI, and fixtures must be rated for damp or wet locations.

Can you replace an old fixture that has aluminum or damaged wiring?

Replacing a fixture can expose old insulation, loose splices, or an undersized or damaged box. These should be corrected at the same visit, since reconnecting a new fixture to unsafe wiring doesn't fix the underlying problem.

Do I need a permit to install or replace light fixtures?

It depends on the jurisdiction and scope. Like-for-like fixture swaps are often exempt, while new circuits, recessed lighting, and outdoor wiring commonly require a permit. Check local requirements or ask your electrician.

Is it safe to change a light fixture myself?

Flipping a wall switch off does not guarantee every conductor in the ceiling box is de-energized. Shut off the breaker, verify with a tester, and call a qualified electrician if you see damaged wiring, aluminum conductors, scorching, or a box that is not secure.

Related Electrical Services

Services that commonly connect to this work

Need something else? Visit the electrical services directory or browse service areas.

Get Started

Need lighting & electrical fixtures?

Call Trident Electric at (855) 599-0507 to discuss your project. Or review the service-area directory.

Call Trident Electric